Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
More than 1 UART ? 0

Hi all, I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
- nrf9e5 uart
710 views

0 replies

Started over 10 years ago
by Pascal
Not Answered
ADC for battery measurment and ports 26,27 and 28 0

Hi, I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end). I am also reading several ports...
- adc
- s110
- nrf51822
935 views

0 replies

Started over 10 years ago
by Antonio
Not Answered
User data cannot be preserved in FLASH on PCA10001? 0

Hi, I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
- pstorage
- s110
- nrf51822
625 views

0 replies

Started over 10 years ago
by scytulip
Not Answered
Using nRF51822 beacon with the Android beacon library 0

Hi, I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs. In order to get more details, I am currently working on integrating the Android...
- advertising
- android
- beacon
- nrf51822
3923 views

0 replies

Started over 10 years ago
by Android Geek
Not Answered
Wheatstone Bridge Interface 0

I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
- adc
- wheatstone
- low-power
- nrf51822
860 views

0 replies

Started over 10 years ago
by Andrew Kohlsmith

Recent in Nordic blog

Intro to ShockBurst/Enhanced ShockBurst

Daniel Veilleux

The first generation of wireless PC accessories to achieve widespread success (the ones that shipped with a dongle in the box) adopted 2.4GHz radios because these radios offered the optimal trade-off between…
- 1 Jan 2018
Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017
Debugging on nrf52840 with GDB from CLI on linux

jfcamel

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017