Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Suggestions for cheapest Arduino basic real-time RFID localization - distance tracking solution? 0

I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
- ble
- arduino
- rfid
- localization
1358 views

0 replies

Started over 10 years ago
by Binyamin
Not Answered
More than 1 UART ? 0

Hi all, I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
- nrf9e5 uart
678 views

0 replies

Started over 10 years ago
by Pascal
Not Answered
ADC for battery measurment and ports 26,27 and 28 0

Hi, I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end). I am also reading several ports...
- adc
- s110
- nrf51822
905 views

0 replies

Started over 10 years ago
by Antonio
Not Answered
User data cannot be preserved in FLASH on PCA10001? 0

Hi, I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
- pstorage
- s110
- nrf51822
589 views

0 replies

Started over 10 years ago
by scytulip
Not Answered
Using nRF51822 beacon with the Android beacon library 0

Hi, I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs. In order to get more details, I am currently working on integrating the Android...
- advertising
- android
- beacon
- nrf51822
3709 views

0 replies

Started over 10 years ago
by Android Geek

Recent in Nordic blog

nRF52840-DK Range Testing With BLE, ZigBee and Thread Protocols at 0, 4 and 8dBm Transmit Power Settings

notsane0

Range testing of any RF scheme is inherently limited by the RF environment, antenna design, tuning and many other factors. The usefulness of range testing is to provide a basis for comparison while keeping…
- 28 Dec 2018
Thingy:52 MOSFET Usage

gamnes

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019