Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
User data cannot be preserved in FLASH on PCA10001? 0

Hi, I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
- pstorage
- s110
- nrf51822
589 views

0 replies

Started over 10 years ago
by scytulip
Not Answered
Using nRF51822 beacon with the Android beacon library 0

Hi, I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs. In order to get more details, I am currently working on integrating the Android...
- advertising
- android
- beacon
- nrf51822
3709 views

0 replies

Started over 10 years ago
by Android Geek
Not Answered
Wheatstone Bridge Interface 0

I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
- adc
- wheatstone
- low-power
- nrf51822
829 views

0 replies

Started over 10 years ago
by Andrew Kohlsmith
Not Answered
nRF51822 Update iOS 7 disconnects 0

When use the "nRFBeacons" app to update the info on my beacon the following happens: Go to update tab. Select "Connect" Press "SW2" on beacon and see the LED begin flashing...
715 views

0 replies

Started over 10 years ago
by David
Not Answered
invalid length long write characteristic gets through 0

I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes. Sending between 1 and 154 bytes works as expected. Sending 155 - 160 bytes gets rejected...
- s110
- nrf51822
626 views

0 replies

Started over 10 years ago
by Travis Hendrickson

Recent in Nordic blog

Reprogram the nRF51822 Beacon Kit to work with iOS 8

rvaessen

When I decided to attempt the reprogramming of my nRF51822 Beacon Kit I read several posts related to the task. The information I needed was there but I found it to be a bit scattered. It was difficult…
- 30 Aug 2015
Nordic's infocenter

Oisin

The Infocenter – our new documentation portal - has now been up and running since June and contains all of our technical documentation. We saw the need for this because we wanted to make our complete…
- 24 Aug 2015
nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020