Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How is it possible to make a control flow during burst transfer with nRF24AP2-USB stick ? 0

Please, It seems that "Flow Control" signal is not available on nRF24AP2-USB. EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
- nrf24ap2-usb chip
1264 views

0 replies

Started over 10 years ago
by Flare77
Not Answered
Suggestions for cheapest Arduino basic real-time RFID localization - distance tracking solution? 0

I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
- ble
- arduino
- rfid
- localization
1359 views

0 replies

Started over 10 years ago
by Binyamin
Not Answered
More than 1 UART ? 0

Hi all, I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
- nrf9e5 uart
678 views

0 replies

Started over 10 years ago
by Pascal
Not Answered
ADC for battery measurment and ports 26,27 and 28 0

Hi, I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end). I am also reading several ports...
- adc
- s110
- nrf51822
906 views

0 replies

Started over 10 years ago
by Antonio
Not Answered
User data cannot be preserved in FLASH on PCA10001? 0

Hi, I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
- pstorage
- s110
- nrf51822
589 views

0 replies

Started over 10 years ago
by scytulip

Recent in Nordic blog

Building a BLE application step by step from scratch

Jocelyn Masserot

Hi all, I'm working on a blog explaining from scratch how to develop a BLE application with nRF518122 chip. Step by step, I explain the different aspects of the embedded system development in a GCC environment…
- 11 Feb 2016
Segger Embedded Studio blog post rev2 DEPRECATED

Michael Dietz

Depreceted see new blog post for new version of embedded studio here: https://devzone.nordicsemi.com/blogs/1032/segger-embedded-studio-a-cross-platform-ide-w-no-c/ #Introduction This post is an introductory…
- 4 Feb 2016
BLE-to-SB quadcopter bridge

Daniel Veilleux

[UPDATE (Feb 8, 2016): I have incorporated the feedback that I received from several link-layer wizards in Trondheim.] Last fall I purchased an inexpensive quadcopter that uses Nordic's ShockBurst (SB…
- 4 Feb 2016

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020