Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Ztest of bluetooth 0

Hi, i need to run this ztest for bluetooth , kindly guide me . link - Nordic\v1.9.1\zephyr\tests\bluetooth\bluetooth Regards, Shikamaru
368 views

0 replies

Started over 2 years ago
by Shikamaru
Not Answered
What can cause RTC1_IRQHandler() to throw Mesh error 8 at 0x00000000? 0

Dear Nordic Experts, This one's a tough nut to crack: The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
690 views

0 replies

Started over 2 years ago
by BlueMike
Not Answered
CMAC calculation failed with SDK 1.9.1 0

SoC: nRF5340 SDK: nRF Connect SDK 1.9.1 CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1. psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
460 views

0 replies

Started over 2 years ago
by Dan2022
Not Answered
Slides from the Electromaker contest Q&A webinar 0
337 views

0 replies

Started over 2 years ago
by Robin M Saltnes
Not Answered
Antenna 0

Forget it, I have found related document and all is clear.
- development
- antenna
- nRF52820
- hardware
500 views

0 replies

Started over 2 years ago
by bob

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019
Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019