Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Issues with getting custom board to enter DFU mode for flashing with mcumgr 0

Problem solved :)
554 views

0 replies

Started over 2 years ago
by nRF60D
Not Answered
Zephyr keyboard driver 0

Dear Nordic, Do we have ready-to-use keyboard driver with scanning/debouncing? I've not found an example or docs about using KSCAN with gpio-connected keyboard...
- development
- software
- nrf5 sdk
- zephyr
- nrf52840
487 views

0 replies

Started over 2 years ago
by Dmitry Kr
Not Answered
Ztest of bluetooth 0

Hi, i need to run this ztest for bluetooth , kindly guide me . link - Nordic\v1.9.1\zephyr\tests\bluetooth\bluetooth Regards, Shikamaru
369 views

0 replies

Started over 2 years ago
by Shikamaru
Not Answered
What can cause RTC1_IRQHandler() to throw Mesh error 8 at 0x00000000? 0

Dear Nordic Experts, This one's a tough nut to crack: The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
691 views

0 replies

Started over 2 years ago
by BlueMike
Not Answered
CMAC calculation failed with SDK 1.9.1 0

SoC: nRF5340 SDK: nRF Connect SDK 1.9.1 CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1. psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
461 views

0 replies

Started over 2 years ago
by Dan2022

Recent in Nordic blog

nRF52 Quadcopter

Jan Tore Guggedal

The nRF52 Quadcopter is a small miniquad that utilizes the nRF52 as both flight controller and for radio communication. The quadcopter uses the Physical Web and Web Bluetooth to make it as easy as possible…
- 12 Aug 2016
Show And Tell: Lys - An Automation Example

Daniel Veilleux

A few weeks ago I was experimenting with the nRF52's radio performance and found myself stuck in a routine that consisted of: Tweaking some parameters in a small piece of firmware Recompiling Downloading…
- 1 Aug 2016
Getting More Out of Make

Daniel Veilleux

There are many reasons why you may want to modify the Makefiles that are included in the SDK examples. For instance, if you are invoking Make from the command line then you will probably also want the…
- 1 Aug 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019