Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Central App stuck after service discovery 0

I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples. I've modified them to run on the PCA10001...

785 views

0 replies

Started over 10 years ago
by Erik Sanchez
Not Answered

nRF51822 RX device can't receive packet from nRF24L01P TX device 0

Hi All, I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device. nRF24L01P TX device Register settings are as follows; Reg.EN_AA=0x00...

686 views

0 replies

Started over 10 years ago
by Mike
Not Answered
S130 programming for the nRF51822 mkit with gcc on a raspberry pi 0

I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
1121 views

0 replies

Started over 10 years ago
by Jimi Cullen
Not Answered
MCP does not start 0

I'm using the nRF51822 eval kit I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working In nRFgo Studio / Device manager pane...
- nrf51822 mcp
591 views

0 replies

Started over 10 years ago
by swjdaenen
Not Answered
SERVER: Write Command on handle 0003, failed 0

the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding. 476;16:12...
- proximity example
558 views

0 replies

Started over 10 years ago
by jerry dzoleko

Recent in Nordic blog

Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017
Debugging on nrf52840 with GDB from CLI on linux

jfcamel

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017
The KEY POINT of example "ble_app_uart"

QQ645116977

This article baed on "pca10040", nRF52832 example code path "examples/ble_peripheral/ble_app_uart" IMPORTANT!!!! board config file of this example located in "components/boards/pca10040.h" and uart…
- 12 Dec 2017