Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
GPIOTE port event and pin events enable issue simultaneously 0

hi all , how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin) i enable the GPIOTE to trigger interrupt event. one for the keyboard which need multiple...
- gpiote
- nrf51822
1731 views

0 replies

Started over 10 years ago
by steven
Not Answered
Cycle speed and cadence sensor data , even after stopping the cycle ? 0

Hi All, I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem. ...
- nrf51422
- ant
711 views

0 replies

Started over 10 years ago
by Robin
Not Answered

Write and read back the FSR register failed 0

Hello Nordic Team, I have a problem with programming the nRF24LE1 chip. I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...

886 views

0 replies

Started over 10 years ago
by MasterAlexei
Not Answered
SDK 6.0.0 OTA DFU iOS compatibility 0

Hi, I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
- s110
- bootloader
- jlink
- keil
- dfu
- nrf51822
1330 views

0 replies

Started over 10 years ago
by Florin
Not Answered
GATT database for a server 0

I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
- gatt nrf51822
- bluetooth low energy
1503 views

0 replies

Started over 10 years ago
by kb

Recent in Nordic blog

Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020