Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Best practices for robust fault recovery with nRF51822? 0

I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
- watchdog
- s110
- nrf51822
1028 views

0 replies

Started over 11 years ago
by Mike Robbins
Not Answered
nRF UART App not resposnding after some time 0

Hi, We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
- s110 v6
- keil
- nrf51822
868 views

0 replies

Started over 11 years ago
by Shafy
Not Answered
SDK6 how to save multiple whitelist? 0

I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
- whitelist
- sdk6.0
- s110
- nrf51822
922 views

0 replies

Started over 11 years ago
by gootoomoon
Not Answered
Parameter not implemented : uint8_t ble_gap_scan_params_t::filter 0

Hi, Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented. Checked for SDK 5.2.0 and 6.0.0. devzone.nordicsemi.com...
- nrf51 sdk softdevice s120
535 views

0 replies

Started over 11 years ago
by Sébastien Despont
Not Answered
StartServiceDiscovery fails after disconnection (VS10, C#) 0

After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again. IsDeviceDiscoveryOngoing was checked before. The...
- masteremulator
- mcp
- c#
1039 views

0 replies

Started over 11 years ago
by Damien

Recent in Nordic blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015