Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

DFU-OTA with S110 v7a3 and nRFToolBox on iPhone 5S 0

Hi Guys, since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following: s110_nrf51822_7...

961 views

0 replies

Started over 10 years ago
by Marius R.
Not Answered
relation in channel and pin 0

Hi All, i would like to know about 1) what is channel in nrf51288? 2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs example channel...
604 views

0 replies

Started over 10 years ago
by renu
Not Answered
uart(with USB to UART bridge) dfu can not work 0

Hi, I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
- dfu with hci
995 views

0 replies

Started over 10 years ago
by jay
Not Answered
Re-connecting iOS(ANCS) takes about 20 sec. 0

Hi. I have been trying get a notification through ANCS. I have created an app which is made by modifying ble_app_ancs sample. It works basically but there is one problem...
- s110
- nrf51822
748 views

0 replies

Started over 10 years ago
by Masa
Not Answered

Consuming too much power in search mode 0

Hello, I'm using the nrf51422 with 210 softdevice. I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...

679 views

0 replies

Started over 10 years ago
by Emily

Recent in Nordic blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016