Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF24L01+ transmitting before auto acknowledgement is complete. 0

I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...

1672 views

0 replies

Started over 10 years ago
by David Watson
Not Answered
Connect another board over UART from nRF51822 mKit board 0

I am using mbed library to get leg up on development. This is the first time I am writing any MCU application and it sure makes things a lot easier. I am using nRF51822...
- mbed
- uart
- nrf51822
1421 views

0 replies

Started over 10 years ago
by Jigar Patel
Not Answered
HID Service on iOS 0

I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
1963 views

0 replies

Started over 10 years ago
by Adam
Not Answered

the speed of large amount of data 0

int main(void) { uint32_t BufferCount; uint32_t err_code; // Initialize leds_init(); timers_init(); buttons_init(); uart_init(); ble_stack_init(); gap_params_init...

950 views

0 replies

Started over 10 years ago
by fitfuel
Not Answered
Gazell library source code. 0

Hi I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
- gazell
- nrf51822
1502 views

0 replies

Started over 10 years ago
by Firek

Recent in Nordic blog

Field-testing how distance affects the behavior of LTE-M and NB-IoT

Petter Myhre

There is an updated field test at the same location from 2022. During the updated field test, we captured more parameters for both LTE-M and NB-IoT devices and, we captured power measurements of the cellular…
- 2 May 2019
SEGGER Embedded Studio Nordic edition updates v4.16

Hung Bui

Recently, we've updated the SEGGER Embedded Studio Nordic edition (SES) to version 4.16 (SES Nordic Edition is special version of SES built specifically for nRF Connect SDK). This updated version introduced…
- 12 Apr 2019
nRF52840-DK Range Testing With BLE, ZigBee and Thread Protocols at 0, 4 and 8dBm Transmit Power Settings

notsane0

Range testing of any RF scheme is inherently limited by the RF environment, antenna design, tuning and many other factors. The usefulness of range testing is to provide a basis for comparison while keeping…
- 28 Dec 2018

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019