Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF24AP2 Rx behaviour
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

810 views

0 replies

Started over 11 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1323 views

0 replies

Started over 11 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn
View Voters Login to vote on this thread 0 Login to vote on this thread
0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1281 views

0 replies

Started over 11 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
902 views

0 replies

Started over 11 years ago
by Pedro Lopes
Not Answered

sd_power_system_off goes directly to main() in sdk5.2
View Voters Login to vote on this thread 0 Login to vote on this thread
0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

1045 views

0 replies

Started over 11 years ago
by julian

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015
nRF51 Qt GCC Example

Jacob Portukalian

Hi Everyone! At Sky Wave Design, we recently switched all of our Nordic development over to using GCC and using Qt Creator as the IDE. We have released our example project on github for those of you…
- 31 Jul 2015
ROM and RAM Management

Øyvind Karlsen

Introduction Here are some tips and tricks to manage your application size. RAM and ROM usage The total RAM usage is: ZI-data + RW-data The total flash usage is: Code + RO-data + RW-data …
- 28 Jul 2015

Nordic DevZone

DevZone monthly Leaderboard

nRF24AP2 Rx behaviour View Voters Login to vote on this thread 0 Login to vote on this thread 0

Logging UART data on a PC View Voters Login to vote on this thread 0 Login to vote on this thread 0

Which priority does softdevice set for SWI2_IRQn View Voters Login to vote on this thread 0 Login to vote on this thread 0

What is the way to have a simple BLE chip work? View Voters Login to vote on this thread 0 Login to vote on this thread 0

sd_power_system_off goes directly to main() in sdk5.2 View Voters Login to vote on this thread 0 Login to vote on this thread 0

Motor Control over BLE with nRF51822 and TB6612FNG

Create Hurricane Tunnel Broker on Raspberry Pi

An appeal to makers - why you should document your project, and how you can do it

ADXL 345 Tutorial

nRF51 Qt GCC Example

ROM and RAM Management

nRF24AP2 Rx behaviour
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Logging UART data on a PC
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Which priority does softdevice set for SWI2_IRQn
View Voters Login to vote on this thread 0 Login to vote on this thread
0

What is the way to have a simple BLE chip work?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

sd_power_system_off goes directly to main() in sdk5.2
View Voters Login to vote on this thread 0 Login to vote on this thread
0