Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

sd_evt_get, not able to receive after sd_flash..... 0

Dear Nordic people, I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...

1060 views

0 replies

Started over 10 years ago
by Jan Krejsa
Not Answered

PAN item 56 TWI module lock-up problem and Rev 3 version of the chip 0

Hi, Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422? Also would you happen to have a time frame as to when the Rev 3 will...

877 views

0 replies

Started over 10 years ago
by ray
Not Answered

Why does re-connection occur 2 times？ 0

Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally. several seconds later, Open Bluetooth in the settings again, and observe the settings...

657 views

0 replies

Started over 10 years ago
by ziv
Not Answered

NRF_WDT: Not able to write to registers 0

Hi, I am trying to power off and/or disable a RR[0] with no success. I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...

1230 views

0 replies

Started over 10 years ago
by Fab
Not Answered

Limit number of packets per connection event? 0

Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...

1103 views

0 replies

Started over 10 years ago
by Paolo D

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019
Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

Simon

This tutorial uses an outdated version of nRF Connect SDK. We recommend using the latest version of nRF Connect SDK when getting started with development. Please see academy…
- 24 May 2019