Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Subsequent sd_ble_gattc_read does not return 0

Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP, received 0x16 bytes of data but there is more to read. Next call to sd_ble_gattc_read using the same connection...
- s120
- receive
- bluetooth low energy
- softdevice
- gatt
1519 views

0 replies

Started over 10 years ago
by Mark Mendelsohn
Not Answered

Why Bluetooth Go to system-off mode, sramon can not be stored. 0

Hello： Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...

1328 views

0 replies

Started over 10 years ago
by bugg
Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

618 views

0 replies

Started over 10 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

800 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1310 views

0 replies

Started over 10 years ago
by Aditya Bansal

Recent in Nordic blog

BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016

Latest guides

Software: Testing concurrent multi-protocol support of Zigbee & BLE over single USB connection to external CPU

Mark Q

Purpose The purpose of this blog is to showcase how a single USB bus can be used as the physical transport for multiple protocols when an external CPU is the controller. Specifications as tested Boards…
- 13 Jul 2021
Peripherals And RF Test: Working around missing shield labels (on the nRF9160 DK)

Embla Flatlandsmo

Table of Contents Objectives What are device tree overlays, and how do they relate to shields? Why are Arduino nodes not recognized in the nRF9160 DK? The workaround: Using the shield as a board ove…
- 25 Jun 2021
Peripherals And RF Test: LVGL on a TFT LCD Display with the nRF9160 DK

Embla Flatlandsmo

Table of Contents Hardware Components Wiring Software Prerequisites Steps Incorporating this into other projects Further reading Attached files This blog post demonstrates how to get a LVGL sample…
- 25 Jun 2021
Software: Using the NCS / West to program the Radio_Test example into the nRF5340-DK for agency testing.

Jay Tyzzer

Background: There is a need to be able to put a Nordic Semiconductors S0C /transceivers into modes where the physical layer and RF characteristics may be ascertained. The radio test example is used to…
- 18 Jun 2021
Software: Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice - Part 2 Central role

Hung Bui

This is part 2 of the series Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice based Bluetooth applications You can find the other parts here: Part 1 - Peripheral Role. Part…
- 5 May 2021
Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021