Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1304 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1257 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
885 views

0 replies

Started over 10 years ago
by Pedro Lopes
Not Answered

sd_power_system_off goes directly to main() in sdk5.2 0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

1034 views

0 replies

Started over 10 years ago
by julian
Not Answered
Bonds/pStorage with fast connection interval 0

I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
- ancs
- pstorage
- timing
- softdevice
- bond manager
901 views

0 replies

Started over 10 years ago
by Eric Salem

Recent in Nordic blog

Measuring Lithium battery voltage with nRF51

Stefan Birnir Sverrisson

Here is an example of a hardware setup to measure the voltage on a Lithium battery with a voltage divider and a connected capacitor. The Lithium battery typically has a voltage range of 2.7 - 4.2 V and…
- 2 Oct 2014
Sniffer application for OS X

RK

I've put up on Sourceforge, a Mac OSX application which interfaces with the Nordic BTLE sniffer software and has some of the functionality of the Windows application Nordic ships with that software package…
- 1 Oct 2014
Getting started with nRF51 development on Mac OS X

Eirik Midttun

Update: Since this blog was originally written the nrfjprog tool has been ported to OS X (now macOS). This means that the flash programming is much simpler, and it is simply a matter of following the documentation…
- 1 Sep 2014

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019