Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

795 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1304 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1257 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
885 views

0 replies

Started over 10 years ago
by Pedro Lopes
Not Answered

sd_power_system_off goes directly to main() in sdk5.2 0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

1034 views

0 replies

Started over 10 years ago
by julian

Recent in Nordic blog

The S110 7.3

Asbjørn Sæbø

We are now releasing the S110 7.3 (s110_nrf51822_7.3.0). This is a new production release in the S110 7.x series. (It will be uploaded today or early next week.) This is a bugfix release - as the release…
- 5 Jun 2015
A presentation on how nRF51 DFU works

Hung Bui

Hi, I attached here some slides that we used in our technical seminar for Device Firmware Update. Download the presentation here: DFU_SDKv8.0_Pub.pdf The presentation covers: What DFU is and what…
- 4 Jun 2015
Parse MQTT message in Wireshark for IoT test

Jun Qing ZOU

Wireshark (version 1.12.5 at the time of writting) lists MQTT as supported protocol but could not parse it from the TCP payload by default. We can add some plugins to enable it. Download the Wireshark…
- 26 May 2015

Latest guides

Bluetooth low energy: Bluetooth Smart and the Nordic's Softdevices - Part 1 GAP Advertising

Hung Bui

This blog series was created as an attempt to fill in the gap between how Bluetooth Smart is defined in the spec and how you can use our APIs and event from our softdevice to do what defined in the spec…
- 10 Dec 2015
nRF5x: Current measurement guide: Introduction

Stian Røed Hafskjold

###Other relevant posts A concise guide to equipment setup, and how to use the development kit for current measurements can be found here: Measuring current with PCA10040 v0.9.0 A post that describes…
- 1 Dec 2015
nRF5x: General PCB design guidelines for nRF51 series

Petter Myhre

When designing a PCB with nRF51, nRF51822 or nRF51422, there are some rules that should be followed in order to get a good working radio/system, with a maximized range. General rule The RF part of the…
- 13 Nov 2015
Software Development Kit: nRF5 SDK Scheduler Tutorial

Einar Thorsrud

2019-02-08: Updated tutorial to cover nRF5 SDK version 15.2. Introduction Scope The following topics will be included in this tutorial: Configuration of the Scheduler library. Using the scheduler with…
- 9 Nov 2015
Bluetooth low energy: Bluetooth low energy central tutorial

Anders Strand

Scope Topics that will be covered include: Before we begin Necessary equipment and software Necessary prior knowledge Setting up the example projects Background theory Central and peripheral roles…
- 4 Nov 2015
Software Development Kit: nRF5 SDK Application Timer Tutorial

Einar Thorsrud

2018-11-23: Updated tutorial to cover SDK version 15.2. 2019-02-08: Improved example project (SDK 15.2) and updated instructions accordingly. Introduction Scope The following topics will be included in…
- 30 Oct 2015