Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

795 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1304 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1257 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
885 views

0 replies

Started over 10 years ago
by Pedro Lopes
Not Answered

sd_power_system_off goes directly to main() in sdk5.2 0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

1034 views

0 replies

Started over 10 years ago
by julian

Recent in Nordic blog

Programming the nRF51822 Beacon Kit with the nRF51DK

Stefan Birnir Sverrisson

One way to program the nRF51822 Bluetooth Smart Beacon Kit is to use the nRF51 DK. This gives you a full scale development platform (the nRF51 DK). This blog will go thru the steps needed to program…
- 7 May 2015
Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015

Latest guides

Getting Started: Adjustment of RAM and Flash memory

AndreasF

The scope of this tutorial is to make it clear how a developer can adjust the RAM and FLASH memory start addresses. The examples demonstrated in this tutorial uses SDK 15.2 The first three Sections explains…
- 7 Dec 2018
Getting Started: nRF52840 Dongle Programming Tutorial

Einar Thorsrud

This tutorial demonstrates how to adapt and program SDK example applications to the nRF52840 dongle using USB DFU. It also describes how to program the dongle via Serial Wire Debug (SWD) using an external…
- 27 Nov 2018
Getting started: Announcing the nRF Connect for Cloud Device API Preview

Markus Tacker (he/him)

We are happy to announce our first release of the nRF Connect for Cloud Device API! Connect your BLE, LTE/NB-IoT or any other device to our free IoT development platform and interact with that device through…
- 12 Oct 2018
Bluetooth low energy: Merging two BLE examples together

Håvard

This is a follow-up to my previous blog post; adding custom commands to a BLE example. I hope it was interesting to see an example of adding the vendor specific Nordic UART service (NUS) into another…
- 6 Sep 2018
Software Development Kit: Getting started with Nordic's Secure DFU bootloader, a step by step guide

Hung Bui

The content of this blog was based on the documentation of BLE Secure DFU example, Bootloader module library and Buttonless DFU service from our SDK. Here we provide you step by step instructions to make it…
- 20 Mar 2017
Getting Started: Introduction to Bluetooth low energy and Bluetooth low energy development (video tutorial)

FormerMember

We have produced a video tutorial in two parts about Bluetooth low energy. The purpose is to give you a developer’s introduction to BLE and the development tools offered by Nordic Semiconductor. NB! Please…
- 6 Oct 2016