Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Subsequent sd_ble_gattc_read does not return 0

Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP, received 0x16 bytes of data but there is more to read. Next call to sd_ble_gattc_read using the same connection...
- s120
- receive
- bluetooth low energy
- softdevice
- gatt
1523 views

0 replies

Started over 10 years ago
by Mark Mendelsohn
Not Answered

Why Bluetooth Go to system-off mode, sramon can not be stored. 0

Hello： Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...

1336 views

0 replies

Started over 10 years ago
by bugg
Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

624 views

0 replies

Started over 10 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

806 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1318 views

0 replies

Started over 10 years ago
by Aditya Bansal

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022