Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

One command execution time on serialization 0

Hi, I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...

746 views

0 replies

Started over 11 years ago
by Elliot.Chao
Not Answered

Has anybody used pervasive dispalay (repaper) on NRF51822 Evaluation Kit? 0

Has anybody got it working? I ported the EPD library from Adruino EPD libray but not sure where its going wrong.

760 views

0 replies

Started over 11 years ago
by Barada Mishra
Not Answered

get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE 0

I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...

2478 views

0 replies

Started over 11 years ago
by julian
Not Answered

HOW do I erase SDK5.2 version of flash and read not, in SDK4.2 can. 0

Hello: Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...

1395 views

0 replies

Started over 11 years ago
by bugg
Not Answered

nRF24LU1 programs a byte through spi command,a strange problem occured... 0

before i write the flash, it has been erased.so ,its value is all 0xff. when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...

652 views

0 replies

Started over 11 years ago
by Albert

Recent in Nordic blog

Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019