Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Modem firmware python script file or dependency missing 0

I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
528 views

0 replies

Started over 3 years ago
by okwestern
Not Answered
Connecting nRF52840 DK to MC3672 Accelerometer and nRF52840 Dongle to Mac 0

Hi, I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
- development
- nrf52840 dongle
- SDK Documentation
- nrf52840 dk
- bluetooth 5
- nrf5 sdk
- spi
- bluetooth le
- nrf52840
- usb
- hardware
659 views

0 replies

Started over 3 years ago
by Jaz
Not Answered
HID Remote and Central . 0

Hi I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 . USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
500 views

0 replies

Started over 3 years ago
by meghna
Not Answered

Please close this thread 0

Please close this thread

483 views

0 replies

Started over 3 years ago
by kerimkilic
Not Answered
NRF52832 SPI and SoftDevice (S132) issue 0

Hello, I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is. The following test works perfectly when SoftDevice...
- software
- s132
- spi
- softdevice
- nrf52832
- production
824 views

0 replies

Started over 3 years ago
by lo

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Software: nRF Desktop on a Development Kit

Priyanka

This tutorial is aimed at implementing the nRF Desktop application on the nRF52840 Development Kit (DK) using the nRF Connect SDK, thereby allowing it to work either as a gaming mouse, keyboard, or dongle…
- 16 Dec 2021
Software: Add DFU support to your application

Simon

This guide is for an older version of the nRF Connect SDK. For a newer guide on Bootloaders and DFU, we recommend https://academy.nordicsemi.com/courses/nrf-connect-sdk…
- 29 Nov 2021
Software: Common fixes for nRF Connect SDK build problems

Sigurd Hellesvik

Does your build fail today, even though it worked fine yesterday? Are you able to build your project on another computer, but not the one you need to use now? Here are eight things you can try to fix these…
- 22 Sep 2021
Peripherals And RF Test: TWI/I2C implementation with nRFx TWIS Driver

Jeff4BLE

Objectives Learn to add and configure an I2C/TWI Master Zephyr driver to an NRF Connect SDK project. Learn to add and configure an I2C/TWI Slave nRFX driver to an NRF Connect SDK project. Demonstrate…
- 4 Aug 2021
Peripherals And RF Test: Using the nRF Connect SDK / West to program the Radio_Test example into the nRF5340 DK for agency testing.

Jay Tyzzer

Using the nRF Connect SDK / West to Program the Radio_Test example into the nRF5340 DK Background: There is a need to be able to put a Nordic Semiconductors System-on-Chip / transceiver into modes where…
- 3 Aug 2021
Software: Updating to the MPSL Timeslot interface

Daniel Veilleux

The "Concurrent Multiprotocol Timeslot API" was introduced with v7.0 of the S110 SoftDevice in 2014. The original purpose was to allow customers to build their own proprietary networks using…
- 2 Aug 2021