Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Using radio_test to test communication between two devices 0

Previously, I compiled and downloaded the radio_test example into two DK boards. I then used the CLI to set the parameters for each board one as TX one as RX On setting...
18 views

0 replies

Started 6 hours ago
by araucaria
Not Answered
npm1300 on-off switch question 0

Hello, I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
21 views

0 replies

Started 8 hours ago
by ecp
Not Answered
nrfjprog command to nrfutil command 0

I'm looking for an nrfutil command to replace this command: nrfjprog --memwr 0x10001080 --val 0x12345678 My goal is to write a serial number to the UICR CUSTOMER[0] register...
22 views

0 replies

Started 9 hours ago
by Phattaw
Not Answered
BLE network hardening tests , blocking PAwR 0

Hi, I am trying to build a BLE PAwR network jammer for wireless network hardening. I have three nrf52840 transmitting on channels 37,38 and 39, which blocks nodes from joining...
- software
- Evaluation
- zephyr
- bluetooth le
- nrf52840
25 views

0 replies

Started 10 hours ago
by aksh_diode
Not Answered
How to calculate SoftDevice usage 0

I am attempting to increase the MTU size on s132 3.0.0 and need to increase the available SoftDevice RAM unproportionally. For every MTU byte I need to give dozens of bytes...
33 views

0 replies

Started 11 hours ago
by Daniel Dakhno

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Getting Started: Adjustment of RAM and Flash memory

AndreasF

The scope of this tutorial is to make it clear how a developer can adjust the RAM and FLASH memory start addresses. The examples demonstrated in this tutorial uses SDK 15.2 The first three Sections explains…
- 7 Dec 2018
Getting Started: nRF52840 Dongle Programming Tutorial

Einar Thorsrud

This tutorial demonstrates how to adapt and program SDK example applications to the nRF52840 dongle using USB DFU. It also describes how to program the dongle via Serial Wire Debug (SWD) using an external…
- 27 Nov 2018
Getting started: Announcing the nRF Connect for Cloud Device API Preview

Markus Tacker (he/him)

We are happy to announce our first release of the nRF Connect for Cloud Device API! Connect your BLE, LTE/NB-IoT or any other device to our free IoT development platform and interact with that device through…
- 12 Oct 2018
Bluetooth low energy: Merging two BLE examples together

Håvard

This is a follow-up to my previous blog post; adding custom commands to a BLE example. I hope it was interesting to see an example of adding the vendor specific Nordic UART service (NUS) into another…
- 6 Sep 2018
Software Development Kit: Getting started with Nordic's Secure DFU bootloader, a step by step guide

Hung Bui

The content of this blog was based on the documentation of BLE Secure DFU example, Bootloader module library and Buttonless DFU service from our SDK. Here we provide you step by step instructions to make it…
- 20 Mar 2017
Getting Started: Introduction to Bluetooth low energy and Bluetooth low energy development (video tutorial)

FormerMember

We have produced a video tutorial in two parts about Bluetooth low energy. The purpose is to give you a developer’s introduction to BLE and the development tools offered by Nordic Semiconductor. NB! Please…
- 6 Oct 2016