Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Power Profiler Kit II Firmware Source 0

Hi everyone, I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
22 views

0 replies

Started 16 hours ago
by Matthias Sokolowski
Not Answered
LIS2DH12 Sample Not Working on nRF54L15-DK — "Device LIS2DH is not ready" 0

Hi everyone, I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
28 views

0 replies

Started 18 hours ago
by DennisDG
Not Answered
Dynamic BLE TX Power Config Fails (nRF5340-DK) 0

Hello everyone, I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
34 views

0 replies

Started 21 hours ago
by diegonovo02
Not Answered
Power profiler Kit II for NRF54L15 0

Hi, When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
29 views

0 replies

Started 23 hours ago
by NickDeLeenheer
Not Answered
How to configure a custom nrf5340 board with HV and DC-DC and a VREGH 3.0V output 0

I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it. I see the documentation on REGULATORS — Regulator control where...
31 views

0 replies

Started 23 hours ago
by lcj

Recent in Nordic blog

Creating a Keil project for a Bluetooth Mesh example (Updated for 0.10.0)

Kristian Skordal

Introduction The recently released nRF5 SDK for Bluetooth Mesh does not provide Keil project files for its example projects. Fortunately, it's relatively easy to set up your own project from scratch.…
- 19 Sep 2017
Using millis() like in Arduino.

schef

Here are two simple functions to use when you want to use timestamps for time measurement. uint32_t millis(void) { return(app_timer_cnt_get() / 32.768); } and for comperison of current with given…
- 18 Sep 2017
Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017
How to build a monitoring and analytics system for your IoT embedded devices almost for free

Yaniv Nis

Embedded devices are no longer ship and forget products. Once deployed, a connected embedded device is updated and provide with services and not just functionality. This paradigm shift requires adopting…
- 5 Sep 2017