Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Notification count in BLE_GATTS_EVT_HVN_TX_COMPLETE event is greater than expected 0

Hello, We are facing an issue where the sum of count in BLE_GATTS_EVT_HVN_TX_COMPLETE events (member of the ble_gatts_evt_hvn_tx_complete_t structure) doesn't match with...
- software
- nrf5 sdk
- softdevice
- bluetooth le
- nrf52840
- s140
- production
23 views

0 replies

Started 2 hours ago
by Joaliasbarb
Not Answered
nRF Connect VScode project issue with GPIO configuration 0

Hi, I created a simple project in VS Code and I have defined the custom board configuration files that I want. In the xxx_defconfig file I have defined CONFIG_GPIO=y but...
15 views

0 replies

Started 2 hours ago
by masterLee
Not Answered
CONFIG_NRFX_TIMER1 was assigned the value y, but got the value n. Missing dependencies: HAS_NRFX || (HAS_NRFX && 0) || ((UART_0_NRF_HW_ASYNC_TIMER = 1 || UART_1_NRF_HW_ASYNC_TIMER = 1 || UART_2_NRF_HW_ASYNC_TIMER = 1 || UART_3_NRF_HW_ASYNC_TIME 0

Im using nrf5340 with nrf connect SDK 2.6. Im trying to follow this post to evaluate hardware timer for reading saadc But I constantly am getting CONFIG_NRFX_TIMER1...
18 views

0 replies

Started 3 hours ago
by IvanR
Not Answered
Adding MCUBOOT and QSPI device to DTS causes no boot 0

I am attempting to get the SMP server sample to work on some custom hardware in order to run a BLE FOTA. I'm using NCS version 2.6.1. I'm able to build the SMP server sample...
24 views

0 replies

Started 6 hours ago
by frankenboom
Not Answered
case about nRF54L15 VS Code Flash error 0

Hi， How to resolve the following burning errors: PDK:PCA10156 0.8.1 SDK ncs v0.8.0 example :peripheral_uart Thank you for all your assistance. Kind regards, Peter...
21 views

0 replies

Started 6 hours ago
by peter.min

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022