Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
With Zephyr, nRF SDK, VSCode and Arduino Nano BLE 33 device configuration files have wrong path 0

I was trying to get a simple Zephyr project to build and run on the Arduino Nano BLE 33 which has a NRF5248. In VSCode with the NRF plugin I select "Add build configuration...
22 views

0 replies

Started 4 hours ago
by marchold
Not Answered
Zephyr Input and GPIO P2 configuration issues on nRF54H20-DK v0.8.2 0

Hi. Currently evaluating this DK. I'm using project that is based on samples\subsys\usb\hid-keyboard example from SDK v2.8.0-rc2. I have added more input pins via Zephyr...
17 views

0 replies

Started 5 hours ago
by Kyrylo
Not Answered
Failed to perform SPI read function on nRF52840dk with BMI270 sensor 0

Hello, I am trying to use SPI driver to read BMI270 IMU data on my nRF52840dk. I stucked at verifying the sensor ID step. According to the datasheet, sensor ID is stored...
- software
- Evaluation
- spi
- nrf52840
21 views

0 replies

Started 5 hours ago
by Shuhao Dong
Not Answered
Failed to clone the repositories when trying to install SDK 2.7.0 0

Hello all, I'm getting stuck on re-installing any SDK and I'm getting the below error. The error: Failed to clone the repositories: Error: HEAD is now at 100befc70c7 [nrf...
24 views

0 replies

Started 7 hours ago
by SOOK
Not Answered
Cracen drivers preventing some ciphers from being compiled in 0

Hello, I am trying to upgrade my project from ncs 2.1.0 to ncs 2.6.1. I am running into some strange issues with mbedtls and I suspect it's because the same ciphers enabled...
41 views

0 replies

Started 8 hours ago
by alexdr5398

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019