Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to Set TX Power for Response Packets in periodic_sync_conn? 0

HI I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
39 views

0 replies

Started 1 day ago
by joey
Not Answered
Synchronization over LTE/NB-IoT - SNTP time accuracy 0

Hi, We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints: Required...
47 views

0 replies

Started 1 day ago
by mjaszczykowski
Not Answered
ALIRO: Expose session error code to the application 0

I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
61 views

0 replies

Started 1 day ago
by Jason
Not Answered
Error in Angle of Arrival Calculation for Direction Finding 0

Hello We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833. We used Nordic's sample codes- ...
108 views

0 replies

Started 2 days ago
by Shivani
Not Answered
Subject: MPSL ASSERT: 69, 108 and HardFault when using ESB (CONFIG_ESB_MPSL_TIMESLOT) with BLE dual connection and ZMS on NCS v3.3.0 / nRF54L10 0

Hi, I'm running NCS v3.3.0 on a Nordic nRF54L10 (nRF54L Series, Cortex-M33) with: - BLE peripheral role, max 2 connections (dual connected simultaneously) - ESB in CONFIG_ESB_MPSL_TIMESLOT...
75 views

0 replies

Started 2 days ago
by Pang0

Recent in the DevZone Blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016