Nordic DevZone

Online Power Profiler

The online profiler is a handy online power estimation tool for evaluation purposes.

Click here to try it out!

DevZone monthly Leaderboard
- Rank
  
  Name
  
  Points
- 1
  
  Turbo J
  
  200
- 2
  
  hmolesworth
  
  100
- 3
  
  Shuhao Dong
  
  99
- 4
  
  Achim Kraus
  
  97
- 5
  
  Leo Mo
  
  91
- 6
  
  lcj
  
  87
- 7
  
  GilDev
  
  67
- 8
  
  Mary
  
  64
- 9
  
  awneil
  
  60
- 10
  
  Golaz
  
  54

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Issue using nrf21540 in GPIO-mode with mode pin and multiple advertising set at 10dBM 0

Hi, We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833. We are developing under nrf connect sdk 3.0...
37 views

0 replies

Started 6 hours ago
by longo92
Not Answered
A question about matter over thread products 0

During the development of a Matter over Thread product, I encountered the following issue: After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
19 views

0 replies

Started 6 hours ago
by paper555
Not Answered
nRF54L15 BLE Current Consumption 0

Hi Nordic Teams : I would like to check the current consumption by BLE DTM. 1. Is the table measurement is from 3.0V input? 2. I find the condition in the datasheet...
14 views

0 replies

Started 7 hours ago
by Webster Yang
Not Answered
Always run old firmware after OTA after changing flash size 0

HI ALL, nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made. Then add the following content to prj.conf sysbuild.conf mcuboot.conf At this...
13 views

0 replies

Started 9 hours ago
by 666
Not Answered
Bus Fault caused by write data to fds 0

I'm developing my application with nrf 52832 and nrf SDK v17. I know NCS is more powerful. I'm currently learning how to use it. But now.I still need my application with...
23 views

0 replies

Started 14 hours ago
by Chaoyue Ying

Recent in Nordic blog

Programming nRF51 with ST-Link & uVision

Milan

Hi, I am planning to design a device based on nRF51-dk but with external programmer. I have ST-Link available so I thought I just provide a simple walk through showing how to set it up. Firstly, here…
- 10 Dec 2014
Visualising your memory usage

Eliot Stock

The linker in the GCC toolchain, ld, produces a *.Map file which shows you how the memory on your micro is being used. This file is a goldmine of information but it's a bit difficult for humans to absorb…
- 2 Dec 2014
Using the ADC with the S110 SoftDevice

Stefan Birnir Sverrisson

A good place to start with getting to know how to use the ADC with the S110 SoftDevice is by using one of the BLE ADC code examples provided on Nordic's Github page, where BLE examples have the "ble_…
- 28 Nov 2014
Nordic sponsoring hackathons

Eirik Midttun

Right before Web Summit - the "Davos for Geeks" - Nordic Semiconductor sponsored its second Hackathon in Dublin: the Hardware Hackathon. As a sponsor Nordic provides hardware and mentors for…
- 21 Nov 2014
Nordic beacons and iOS

Asbjørn

The beacon market is going in various directions with regard to format and limitations, but the nRF51822 can support all the various BLE based beacons as it’s just a specific type of non-connectable BLE…
- 18 Nov 2014
Make your own "Remote Control" app

Jason

Flow us to make your own RC App to control everything so easy. web-site
- 13 Nov 2014