Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
low level interrupt not firing after porting from SDK 15.3 to SDK 17.0.2 0

I have a working project where pin 16 is configured as a low-level interrupt source. it is working well with SDK 15.3 after porting to SDK 17.0.2, it is not triggering...
376 views

0 replies

Started over 3 years ago
by kobyfr
Not Answered
Thank you 0

Hello Nordic Support Engineers and fellow developers ... Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
511 views

0 replies

Started over 4 years ago
by Tim
Not Answered
Website links/downloads for Thingy91 removed? 0

Hi, I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
328 views

0 replies

Started over 4 years ago
by justinm_nz
Not Answered
How to measure the power consumption of NRF5340 0

I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
- development
- software
- nRF53
- nRF5340
639 views

0 replies

Started over 4 years ago
by huangjingyu
Not Answered
Anyone have the Eagle libraries for Taiyo Yuden's EYSNSNZWW (it contains the nRF52811) 0

Any pointers would be welcome. /Trivik
371 views

0 replies

Started over 4 years ago
by saccade

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020