Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Publish timeout handler of a model called during opcode handling of a message in the same model (or vice versa) 0

Hi, This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
361 views

0 replies

Started over 4 years ago
by Mathias
Not Answered
New nRF52840 finger tip size module with Type-C Dongle fully compatible with Nordic dongle 0

Hi to all Nordic product lovers, This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
1217 views

0 replies

Started over 4 years ago
by Nguyen Hoan Hoang
Not Answered
Bitwise operations on uint8_t / Integer promotion 0

Hi, I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
1021 views

0 replies

Started over 4 years ago
by fuesel
Not Answered
CMSIS tool 0

Hello, Is there a way to show only enabled options in CMSIS tool? If not, that would be a nice enhancement for future versions. Thanks, Sam
825 views

0 replies

Started over 4 years ago
by Sam123
Not Answered
Erase 0

I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
402 views

0 replies

Started over 4 years ago
by Malcolm

Recent in Nordic blog

Rust bindings to nrf52 series

Coleman McFarland

In mid-2017, I came across this project by James Munns. It essentially wraps the C SDK for nRF52 development boards, and provides bindings that can be called from Rust. James gave a talk to the Rust DC…
- 12 Jan 2018
Show And Tell: Poly - Building an RC Airplane The Hard Way

Daniel Veilleux

I've been looking for an excuse to write a low-latency, Enhanced ShockBurst (ESB), radio protocol that I can reuse when building remote control toys. Although Bluetooth is great for a lot of use cases…
- 5 Jan 2018
Bluetooth on a desktop computer (Windows, Mac, Linux)

kbaud

Posting this here in an effort to save the time of anyone else who is wanting to control a device from a desktop computer. Our application is a motor control device that is wirelessly controlled from…
- 4 Jan 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019