Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Modem firmware python script file or dependency missing 0

I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
586 views

0 replies

Started over 4 years ago
by okwestern
Not Answered
Connecting nRF52840 DK to MC3672 Accelerometer and nRF52840 Dongle to Mac 0

Hi, I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
- development
- nrf52840 dongle
- SDK Documentation
- nrf52840 dk
- bluetooth 5
- nrf5 sdk
- spi
- bluetooth le
- nrf52840
- usb
- hardware
723 views

0 replies

Started over 4 years ago
by Jaz
Not Answered
HID Remote and Central . 0

Hi I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 . USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
545 views

0 replies

Started over 4 years ago
by meghna
Not Answered

Please close this thread 0

Please close this thread

527 views

0 replies

Started over 4 years ago
by kerimkilic
Not Answered
NRF52832 SPI and SoftDevice (S132) issue 0

Hello, I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is. The following test works perfectly when SoftDevice...
- software
- s132
- spi
- softdevice
- nrf52832
- production
901 views

0 replies

Started over 4 years ago
by lo

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017

Latest guides

Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019
Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

Simon

This tutorial uses an outdated version of nRF Connect SDK. We recommend using the latest version of nRF Connect SDK when getting started with development. Please see academy…
- 24 May 2019