Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
I2S driver in SDK 16 0

Did anyone try to drive WS281b LED with I2S using nrf5 SDK 16 there're some differences in the new version
472 views

0 replies

Started over 5 years ago
by Mark93
Not Answered
External NAND flash with nRF5340 (non-SPI) 0

I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
- flash
- hardware
- Pre-production
- nRF5340
1532 views

0 replies

Started over 5 years ago
by mattgaidica
Not Answered
RAM START ADDRESS 0

Hi I try to run BLE HRS collector example. when I run the project, in RTT terminal I have these error 00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
- s130
- software
- Evaluation
- nrf51
- nrf51802
946 views

0 replies

Started over 5 years ago
by M.A.N.
Not Answered
Google: Say hello to OpenSK: a fully open-source security key implementation using nRF52840 Dongle (among others) 0

Google open-sources the firmware needed to build hardware security keys Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
2906 views

0 replies

Started over 5 years ago
by LarsH
Not Answered
Mesh 4.0 SDK Flash Manager - Storing values 0

I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
- development
- software
- flash
- mesh
- nRF Mesh
- nrf52832
845 views

0 replies

Started over 5 years ago
by joao

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019