Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to use nrf54L15-dk with external host through hci uart application 0

Hi, I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
15 views

0 replies

Started 16 hours ago
by Abhinav152
Not Answered
Pin assignment for UART on the nRF54L15DK 0

Hello. I am testing UART connectivity using the nRF54L15DK. After assigning pins to TX and RX, there were combinations that worked fine and combinations that didn't. There...
18 views

0 replies

Started 17 hours ago
by a.da
Not Answered
Some problems about Periodic advertising 0

The scanner can be informed of the synchronization information as soon as it receives an ADV_EXT_IND PDU, and then it can later scan only AUX_SYNC_IND PDUs. at this point...
14 views

0 replies

Started 19 hours ago
by Caesarzhou
Not Answered
Matter Generating Unique Factory Data and Certificates on Windows 0

I'm working with the Matter Template example and creating a sensor monitoring device on the nRF52840 platform, and I'm developing on a Windows environment with SDK 2.9.0....
- development
- software
- nRF Connect SDK
- zephyr
- thread
- nrf52840
18 views

0 replies

Started 22 hours ago
by rkap
Not Answered
SW got stuck during reading internal TEMP sensor 0

Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
38 views

0 replies

Started 2 days ago
by Tomas S.

Recent in Nordic blog

On nRF Connect for iOS and its Unnecessary BitField Collection in Swift

Dinesh Harjani

For the longest time we’ve had this idea, of turning one of our most-used Swift Collection Types into a simple one-instruction comparison call, down at the assembly level, to check whether an element belongs…
- 23 Jul 2020
Measuring PSM Sleep Current on the nRF9160-DK

notsane0

Overview In this blog, you will measure the PSM floor current for the rev. 2 version of the nRF9160 SiP. Requirements Hardware You will need: an nRF9160-DK (the one used here was v1.0.0). Be sure that…
- 7 May 2020
Developing for the nRF52820 with nRF5 SDK v16.0.0

bjorn-spockeli

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development. Introduction The nRF52820 IC is…
- 19 Mar 2020

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019