Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nrf_delay_ms() is not available for usbd communication (usbd_cdc_acm) 0

Hello, World Please note that the following questions may be difficult to read as the text was created using a translation tool. I have downloaded version 17.0.2 of the...
- software
- Evaluation
- nrf5 sdk
- nrf52840
- usb
21 views

0 replies

Started 16 hours ago
by Rion
Not Answered
Matter firmware can not run in custom board(nrf54l15) 0

I have an nRF54L15DK and a custom-designed nRF54L15 board. These two boards use different pins for peripherals. The NCS version used is v2.9.0. I compiled a Matter project...
28 views

0 replies

Started 17 hours ago
by jared_jia
Not Answered
unknow data when use qspi panel 0

Hi all, I applied QSPI driver on NCS 2.4.0 with QSPI LCD panel and I encountered the problem. The red area is the data I sent, but the blue area is not what I sent....
15 views

0 replies

Started 17 hours ago
by Wayne_Chang
Not Answered
How to use nrf54L15-dk with external host through hci uart application 0

Hi, I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
15 views

0 replies

Started 17 hours ago
by Abhinav152
Not Answered
Pin assignment for UART on the nRF54L15DK 0

Hello. I am testing UART connectivity using the nRF54L15DK. After assigning pins to TX and RX, there were combinations that worked fine and combinations that didn't. There...
18 views

0 replies

Started 18 hours ago
by a.da

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020