Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
GPIO9 & 10 won't operate independently using zephyr (but OK with rRF5 SDK) 0

I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not. Let me emphasise THE BOARD IS WORKING...
26 views

0 replies

Started 15 hours ago
by Nick_RA
Not Answered
"VDD_GPIO should be applied after VDD has been supplied" 0

Dear Nordic and community, I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
35 views

0 replies

Started 16 hours ago
by Dirk_
Not Answered
TX max power impacted if usng 1.8V on VDD 0

Hi Nordic engineer I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start. Due to limitation of power resource...
30 views

0 replies

Started 17 hours ago
by huangsong
Not Answered
Enabling Wifi on nRF7002 0

Hello everyone, I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
40 views

0 replies

Started 18 hours ago
by Tudor B.
Not Answered
Upload certificat to custom board 0

Hi all, I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
23 views

0 replies

Started 18 hours ago
by simon884

Recent in Nordic blog

Thingy:52 based Weather Station

Krzysztof Szewczyk

Weather station created from two Nordics eval-boards (Thingy:52 and nRF52840-Preview-DK). Source code and hardware files are available. http://evalspace.com/weather-station/
- 29 Oct 2017
How to build continuous integration and delivery process for embedded SW development

Yaniv Nis

If automated testing, continuous integration, and delivery processes are top of mind for you, but you are not sure how to start implementing it for embedded SW development - take a look at the following…
- 3 Oct 2017
Multiple channels in RTT

Krzysztof Zaraska

Segger RTT (Real-Time Terminal) supports multiple data channels. RTT Viewer uses channel 0 only, and implements multiple virtual terminals on top of this. The terminal can be switched by SEGGER_RTT_SetTerminal…
- 29 Sep 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019