Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How does the Online Power Profiler for Wi-Fi tool calculate energy consumption 0

How does the Online Power Profiler for Wi-Fi tool calculate energy consumption, and is there a formula or document explaining its energy consumption calculation principle...
9 views

0 replies

Started 3 hours ago
by ChengQing Zhao
Not Answered
How to change the Link request interval of OpenThread in NCS 0

As shown in the figure above, if I need to modify the time interval of OpenThread's Link request or parent request, how can I do it? Thank you NCS 2.6.0 NRF52840
17 views

0 replies

Started 4 hours ago
by Quay
Not Answered
Why does it take so long for nRF9151DK to register on NB network? 0

I am developing a product for a customer using NRF9151(ncs2.7.0, modem fw: mfw_nrf91x1_2.0.2). While verifying it on the DK board, I discovered an issue. When the system starts...
- development
- software
- nb-iot
- nRF9151
- C
16 views

0 replies

Started 4 hours ago
by duxinglang
Not Answered
devicetree gui not showing in vs code 0

I created a blinky example in zephyr and created my board with Create a new board The build goes well and runs well. The problem is that the device tree gui does not run and...
18 views

0 replies

Started 6 hours ago
by hmihmi
Not Answered
How can I implement PSK pairing for BLE? 0

Hello, I'm using nRF SDK 2.7.0 and trying to implement PSK type bonding. From quick ChatGPT search it looks like in past SDK versions there was a way to inject pre shared...
12 views

0 replies

Started 9 hours ago
by GuyYaniv

Recent in Nordic blog

Driving WS2812B LEDs using I2S on the Nordic nRF52832

Mahesh Venkitachalam

In this article, I use the I2S peripheral of the Nordic nRF52832 to generate the waveforms required to drive the popular WS2812B RGB LEDs. http://electronut.in/nrf52-i2s-ws2812/
- 18 Aug 2017
Walkthrough of Nordic Thingy:52 Node.js Raspberry Pi demos

gamnes

Thingy:52 Node.js Raspberry Pi Interface This blog post is a follow up to the Nordic Thingy:52 node.js/Raspberry Pi demos blog post, and will described how you can run and what to expect from each of…
- 17 Aug 2017
ble_app_hrs_freertos running in Atollic TrueSTUDIO

jmag999

This post describes how you can get the ble_app_hrs_freertos example project running in Atollic TrueSTUDIO 8.0 on a pca10040 board. This is a managed make build, it does not rely on the makefile provided…
- 14 Aug 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019