Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Error when flashing nrf5340 custom board in HV DC/DC mode with 3V0 set using a segger jlink plus 0

I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
39 views

0 replies

Started 1 day ago
by lcj
Not Answered
Unable to Create New Build Config in nRF Connect (NCS 3.0) – “Add Build Configuration” Always Fails 0

Hi, I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
37 views

0 replies

Started 1 day ago
by witc
Not Answered
Question Regarding Current Measurement on the nRF52840 DK (P22 Header) 0

Hello, Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project. I am working with the nRF52840 DK, and I am trying...
28 views

0 replies

Started 1 day ago
by Tubald
Not Answered
Can not receive periodic advertising reports nrf52833 0

Hi, I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone). I am using bindings to the softdevice controller ( https://github...
42 views

0 replies

Started 1 day ago
by Tomer Eliahu
Not Answered
RTT viewer is not working on nRF54L15 0

Hi Nordic team, I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
- development
- software
- nRF54L15
- zephyr
44 views

0 replies

Started 1 day ago
by barfiii

Recent in Nordic blog

FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015