Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Current consumption in nrf52833, sdk version 2.9.0 , not able to use : pm_state_force(0u, &(struct pm_state_info){PM_STATE_SUSPEND_TO_IDLE, 0, 0}); 0

I am getting an error of "undefined reference to `pm_state_force" . Also, the output files, config file is not showing the command : CONFIG_PM =y prj.conf file has : ...
32 views

0 replies

Started 1 day ago
by Kuldeep Chandel
Not Answered
VDD_EXT on custom board with nRF54H20 0

Hello, We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7). The voltage we see on VDD_EXT is about 1.3V instead...
30 views

0 replies

Started 1 day ago
by Mykhaylo
Not Answered
how testing of enhanced multi-admin 0

Hi, I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4. Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
19 views

0 replies

Started 1 day ago
by chiba
Not Answered
Error when flashing nrf5340 custom board in HV DC/DC mode with 3V0 set using a segger jlink plus 0

I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
41 views

0 replies

Started 1 day ago
by lcj
Not Answered
Unable to Create New Build Config in nRF Connect (NCS 3.0) – “Add Build Configuration” Always Fails 0

Hi, I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
41 views

0 replies

Started 1 day ago
by witc

Recent in Nordic blog

FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015