Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Step-by-step Debugging Issue on VSCode with ARM GCC (nRF52811, SDK 17.1) 0

Hello everyone, I’m facing an issue with step-by-step debugging in VSCode using the ARM GCC compiler with an nRF52811 microcontroller and Nordic’s SDK 17.1. Here are the...
27 views

0 replies

Started 1 day ago
by kza
Not Answered
ncs 2.8.0 sysbuild BOARD and BOARD_QUALIFIERS not set 0

I'm migrating an nRF52840 project from ncs 2.7.0 to ncs 2.8.0. We pass the board in to the west build command line. Our CMakeLists.txt uses the BOARD & BOARD_QUALIFIERS to...
34 views

0 replies

Started 1 day ago
by denis
Not Answered
Device tree configuration for SX1261 on a Insight 4520 SIP based on nRF52832 0

Hello, I have a Insight ISP4520 SIp which include a nRF52832 chip and a SX1261 for Lora radio https://www.insightsip.com/products/combo-smart-modules/isp4520 The internal...
21 views

0 replies

Started 1 day ago
by vincent_itk
Not Answered
Change TX power for the nRF52840-DK 0

Hi, I am testing the Peripheral Heart Rate Monitor with the Coded PHY application for the nRF52840-DK kit. So, I am using two kits, one running the Peripheral Heart Rate...
28 views

0 replies

Started 1 day ago
by Dayrene
Not Answered
Question about NRF5340 LE PHY selection. 0

nrf5340_audio application ， unicast_audio and broadcast_audio samples in zephyr， Are these all LE_2M by default ? If I want to use LE_1M, how to change ? Modify prj.conf...
- code
- software
- Evaluation
- LE Audio
- 2.4 ghz
- bluetooth le
- nRF5340
25 views

0 replies

Started 1 day ago
by HaiwenChen

Recent in Nordic blog

Large scale Bluetooth mesh testing

Omkar Kulkarni

Update: Jan-2024, with NCS v2.5.1 Reliability and latency are the key parameters to be optimized to achieve a seamless experience for the end users in the Bluetooth mesh based lighting control systems…
- 13 Apr 2023
Debunking misconceptions: A technical analysis of nRF5 SDK and nRF Connect SDK

Tiago Monte

Embedded software for IoT applications often requires a high degree of optimization, especially around fitting the image into constrained Flash/RAM space and reaching tight power consumption targets. In…
- 5 Apr 2023
Up to 4x battery life: The benefits of assisted GPS in asset tracking

Charlie

Nordic provides a unique one-stop solution for asset tracking applications. We provide the hardware, software, connectivity, and the cloud services. Our low-power nRF9160 SiP has a multimode modem that…
- 23 Mar 2023

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019