Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
calling sd_ble_gap_whitelist_set crashes my application 0

working with a nrf52833, soft device 140. I am trying to setup a whitelist with a known addresses before I start scanning. I am calling the following code before my main...
35 views

0 replies

Started 1 day ago
by jacob jacob
Not Answered
About CONFIG_BT_ID_MAX and BT_STACK_ID_LUT_SIZE 0

HI, I am using the NCS V2.9.0 ,nrf Desktop sample; I want to mouse can pair 3 hosts, and i can select one of them connect and work; I set CONFIG_BT_MAX_PAIRED=3 and...
32 views

0 replies

Started 1 day ago
by gandyhuang
Not Answered
GPIO9 & 10 won't operate independently using zephyr (but OK with rRF5 SDK) 0

I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not. Let me emphasise THE BOARD IS WORKING...
29 views

0 replies

Started 1 day ago
by Nick_RA
Not Answered
"VDD_GPIO should be applied after VDD has been supplied" 0

Dear Nordic and community, I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
37 views

0 replies

Started 1 day ago
by Dirk_
Not Answered
TX max power impacted if usng 1.8V on VDD 0

Hi Nordic engineer I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start. Due to limitation of power resource...
32 views

0 replies

Started 1 day ago
by huangsong

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022