Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
OTA DFU on 54L15 0

Hi all, we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
- development
- software
- nRF54L15
- thread
- dfu
35 views

0 replies

Started 1 day ago
by Allan-led
Not Answered
Configuring PIN 0.00 and P0.01 as GPIO on NRF5340 with nrf connect sdk v3.0.2 0

Hello, We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
43 views

0 replies

Started 1 day ago
by byte
Not Answered
54L15 using DPPI to link 3 peripheral in different power domain 0

Hi I am developing in 54L15. Now use DPPI to link TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP, it works fine. Now I want to trigger a GPIO signal through...
50 views

0 replies

Started 1 day ago
by ToothlessYY
Not Answered
Bluetooth Qualification Using Nordic DNs for third party modules 0

Post: Hi Nordic Team, We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
57 views

0 replies

Started 1 day ago
by MTB-C
Not Answered
Regarding the issue of space occupation on nrf52833 using the Secure Transport Layer (DTLS) 0

I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
41 views

0 replies

Started 1 day ago
by Idle-xu

Recent in Nordic blog

Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015