Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Disable and enable BLE OTA/DFU service 0

Hi, Platform: nRF54L15, SDK 2.9 The application is Matter + BLE. CONFIG_CHIP_DFU_OVER_BT_SMP & MCUBoot are part of the configuration. As soon as we enable the BLE...
20 views

0 replies

Started 1 day ago
by SubuMuthu
Not Answered
Ring Buffer Maximum Size 0

Hello, I'm reading about 700 values from an LSM6SDO gyro/accelerometers per second and need to store them, before sending them over bluetooth once where I store them is...
21 views

0 replies

Started 1 day ago
by connorshannon
Not Answered
Flash nRF52840 dongle with Sweyntooth firmware 0

Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
22 views

0 replies

Started 1 day ago
by DavidXie
Not Answered
Warning FLASH_SIMULATOR unassigned starting from NCS SDK 2.7.0 due to missing default flash_sim.overlay from build 0

I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
23 views

0 replies

Started 1 day ago
by Alfredo Antolinez
Not Answered
Run time control of MCU Manager 0

We are looking to do DFU over UART to the Application as described in DevAcademy nRF Connect SDK Intermediate, Lesson 8, Exercise 1, Step 5. However, we have only one UART...
- development
- software
- dfu
- nRF5340
19 views

0 replies

Started 1 day ago
by bbbakke

Recent in Nordic blog

nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020