Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Multiple advertisement (ibeacon + custom connectable advertisement) on nrf52 +4

Hi, I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
1504 views

0 replies

Started over 5 years ago
by NO69124
Not Answered
Why the HID device can't be seen from nRFConnect? 0

Hi, I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
369 views

0 replies

Started over 5 years ago
by SevenZeng
Not Answered
Why the HID device can't be seen from nRFConnect? 0

Hi, I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
288 views

0 replies

Started over 5 years ago
by SevenZeng
Not Answered

nRF51822 and low power: can it really go below ~600 µA? 0

I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it). The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...

374 views

0 replies

Started over 5 years ago
by Lisandro Damián Nicanor Pérez Meyer
Not Answered
Problem compiling Thingy 52 with Segger Embedded Studio 0

I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
695 views

0 replies

Started over 5 years ago
by Niteesh

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019