Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Can I get current transmitting channel in nRF52832 0

Hi, I'm wondering if I can get current transmitting channel during a connection. So Is there a way I can directly read current transmitting channel? If not, is...
- channel
- 10040 nrf52832 s132
1302 views

0 replies

Started over 8 years ago
by saintnever
Not Answered

How exactly the "recursive" calls to "app_sched_execute" are fixed in SDK14 Bootloader ? 0

This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below: devzone.nordicsemi...

906 views

0 replies

Started over 8 years ago
by sdaexpert
Not Answered

advertisement with whitelisting 0

hi. How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...

1082 views

0 replies

Started over 8 years ago
by anuja
Not Answered

througput parameter 0

why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)? Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...

875 views

0 replies

Started over 8 years ago
by Stayhungry
Not Answered

why Error: L6218E: Undefined symbol app_sched_init (referred from main.o). 0

Hi, I am using Keil IDE to develop nRF51822 project. in main(), the command line APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE); has Error : L6218E...

1780 views

0 replies

Started over 8 years ago
by DYNAMICTOYS

Recent in the DevZone Blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018