Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to connect Proxomity , UART and DFU with all at the same time with single connection. 0

Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
- bluetooth low energy
531 views

0 replies

Started over 7 years ago
by Sahil Bharwani
Not Answered

Question about the PDM/PCM of nrf52832 0

Dear Nordic employee: 1、 what do I have? I have a thingy52 develop kit（nrf52832） 2、what is my purpose? the quality of thingy52 audio demo is not good（iphone7）...

1642 views

0 replies

Started over 7 years ago
by victor_CHINA
Not Answered
How to optimize power consumption when UART run? 0

Hello Nordic, My development environment: SDK>> NRF51822_SDK10, SoftDevice>> S130 Example>> ble_app_uart I am looking forward to your reply! Thanks. Best Regards...
- uart power consumption
910 views

0 replies

Started over 7 years ago
by Andy
Not Answered
Unable to start nRF connect(BLE) 0

Dear friends, according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps: Connect a development kit or dongle to...
- ble
- nrfconnect
813 views

0 replies

Started over 7 years ago
by xvhongpeng
Not Answered

MESH sd_ble_enable NRF_ERROR_NO_MEM 0

Hi I have add some function call like sd_ble_enable in mesh example, I test to get then I set the address and all sd_ble_cfg_set is ok but when I call "sd_ble_enable...

1181 views

0 replies

Started over 7 years ago
by mark

Recent in Nordic blog

Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019