Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Unable to see NRF_LOG BLE SDK 12.3 0

I am using SEGGER Studio on MacOSx. When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio. However...
- nrf51822 nrf_log segger
980 views

0 replies

Started over 7 years ago
by zed
Not Answered
nRF Cloud Gateway Error connecting gateway 0

Hello, I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
- nrf52 pca10040 nrfconnect
- nrfCloud
1463 views

0 replies

Started over 7 years ago
by carlos carrizosa
Not Answered
Finding secondary services using dongle, linux library 0

Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0. I can see/connect to the device I am trying...
- nrf51dongle service discovery
569 views

0 replies

Started over 7 years ago
by timrcooper
Not Answered
what facter will influence the speed of sending data 0

when use sd_ble_gatts_hvx() send data must need 300ms what facter will influence the speed of sending data ,please help me ,thank you very much
- 10040 nrf52832 s132
600 views

0 replies

Started over 7 years ago
by happykelvin
Not Answered
nRF52: OneWire HDMI CEC 0

Hey, I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832. I would be very grateful if anybody could share the library or give...
- nrf52
- one-wire
1679 views

0 replies

Started over 7 years ago
by Sorrow91

Recent in Nordic blog

Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019