Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Illegal use of the EPSR - uart fault 0

Hi, i have some code thats based off of the uart_async_adapter.c example code. I' m getting a `usage fault` which i've traced to uart_irq_handler. it happens when i try...
- development
- software
- zephyr
- nrf52832
28 views

0 replies

Started 19 hours ago
by michaelmac
Not Answered
Pushing keys from KMU to ECB? 0

Hi! I'm storing a key in the KMU for use by the ECB. If I set the slot's destination address to an address in RAM, the KMU pushes the key there correctly, but if I instead...
36 views

0 replies

Started 22 hours ago
by SebastianA
Not Answered
Issue of nRF54L15’s GPIO high voltage is lower than VDD 0

Hi Support Team The VDD of customer’s nRF54L15 board is 3V, but the high voltage of P1.10 is about 1V. Did you meet this issue before? Customer needs the output high voltage...
25 views

0 replies

Started 22 hours ago
by Tom.Fu
Not Answered
When a Matter device is powered back on, how can the lock status be updated to the Apple Home? 0

If the lock's status changes while the device is powered off, causing a mismatch between the lock and the Apple Hub, how can I immediately update the status upon powering...
18 views

0 replies

Started 23 hours ago
by SunHuang
Not Answered
RES Issue with nRF54L15 QFN 0

The problem has been resolved, please ignore this post
- nRF54L15
54 views

0 replies

Started 1 day ago
by Derek Yang

Recent in Nordic blog

The S110 7.3

Asbjørn Sæbø

We are now releasing the S110 7.3 (s110_nrf51822_7.3.0). This is a new production release in the S110 7.x series. (It will be uploaded today or early next week.) This is a bugfix release - as the release…
- 5 Jun 2015
A presentation on how nRF51 DFU works

Hung Bui

Hi, I attached here some slides that we used in our technical seminar for Device Firmware Update. Download the presentation here: DFU_SDKv8.0_Pub.pdf The presentation covers: What DFU is and what…
- 4 Jun 2015
Parse MQTT message in Wireshark for IoT test

Jun Qing ZOU

Wireshark (version 1.12.5 at the time of writting) lists MQTT as supported protocol but could not parse it from the TCP payload by default. We can add some plugins to enable it. Download the Wireshark…
- 26 May 2015

Latest guides

Bluetooth low energy: Bluetooth Smart and the Nordic's Softdevices - Part 1 GAP Advertising

Hung Bui

This blog series was created as an attempt to fill in the gap between how Bluetooth Smart is defined in the spec and how you can use our APIs and event from our softdevice to do what defined in the spec…
- 10 Dec 2015
nRF5x: Current measurement guide: Introduction

Stian Røed Hafskjold

###Other relevant posts A concise guide to equipment setup, and how to use the development kit for current measurements can be found here: Measuring current with PCA10040 v0.9.0 A post that describes…
- 1 Dec 2015
nRF5x: General PCB design guidelines for nRF51 series

Petter Myhre

When designing a PCB with nRF51, nRF51822 or nRF51422, there are some rules that should be followed in order to get a good working radio/system, with a maximized range. General rule The RF part of the…
- 13 Nov 2015
Software Development Kit: nRF5 SDK Scheduler Tutorial

Einar Thorsrud

2019-02-08: Updated tutorial to cover nRF5 SDK version 15.2. Introduction Scope The following topics will be included in this tutorial: Configuration of the Scheduler library. Using the scheduler with…
- 9 Nov 2015
Bluetooth low energy: Bluetooth low energy central tutorial

Anders Strand

Scope Topics that will be covered include: Before we begin Necessary equipment and software Necessary prior knowledge Setting up the example projects Background theory Central and peripheral roles…
- 4 Nov 2015
Software Development Kit: nRF5 SDK Application Timer Tutorial

Einar Thorsrud

2018-11-23: Updated tutorial to cover SDK version 15.2. 2019-02-08: Improved example project (SDK 15.2) and updated instructions accordingly. Introduction Scope The following topics will be included in…
- 30 Oct 2015