Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Pushing keys from KMU to ECB? 0

Hi! I'm storing a key in the KMU for use by the ECB. If I set the slot's destination address to an address in RAM, the KMU pushes the key there correctly, but if I instead...
31 views

0 replies

Started 18 hours ago
by SebastianA
Not Answered
Issue of nRF54L15’s GPIO high voltage is lower than VDD 0

Hi Support Team The VDD of customer’s nRF54L15 board is 3V, but the high voltage of P1.10 is about 1V. Did you meet this issue before? Customer needs the output high voltage...
23 views

0 replies

Started 18 hours ago
by Tom.Fu
Not Answered
Wake up main thread on any interrupt 0

Hi, Is there a way to make the main thread to execute after any interrupt? For now, I have something like this (ncs 2.7.0): in main thread : In each IRQ handlers...
16 views

0 replies

Started 19 hours ago
by Ben_Squar3d
Not Answered
When a Matter device is powered back on, how can the lock status be updated to the Apple Home? 0

If the lock's status changes while the device is powered off, causing a mismatch between the lock and the Apple Hub, how can I immediately update the status upon powering...
17 views

0 replies

Started 19 hours ago
by SunHuang
Not Answered
RES Issue with nRF54L15 QFN 0

The problem has been resolved, please ignore this post
- nRF54L15
54 views

0 replies

Started 1 day ago
by Derek Yang

Recent in Nordic blog

Upgrade RADVD for IoT on Raspberry Pi 2

Jun Qing ZOU

The RADVD deamon in Raspberry pool is version 1.8.5 (up to Raspberry 2015-02-16). root@raspberrypi:~/radvd# apt-cache policy radvd radvd: Installed: 1:1.8.5-1 Candidate: 1:1.8.5-1 Version table…
- 25 May 2015
Workaround needed for TWI driver (nrf_drv_twi) in SDK v8.1 (TWI_COUNT missing)

Hung Bui

In SDK v8.1 we added the TWI driver (nrf_drv_twi.c). Unfortunately the nrf_drv_config.h file wasn't updated correctly with the new driver. The symptom is the error with "TWI_COUNT is missing". Here…
- 20 May 2015
Common FAQs on DFU

Hung Bui

If you are looking for a place to get started with DFU, please have a look at this presentation here and the tutorial here. In this post, we cover some in depth Q&A topics regarding Device Firmware…
- 15 May 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019