Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Unable to see NRF_LOG BLE SDK 12.3 0

I am using SEGGER Studio on MacOSx. When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio. However...
- nrf51822 nrf_log segger
936 views

0 replies

Started over 7 years ago
by zed
Not Answered
nRF Cloud Gateway Error connecting gateway 0

Hello, I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
- nrf52 pca10040 nrfconnect
- nrfCloud
1400 views

0 replies

Started over 7 years ago
by carlos carrizosa
Not Answered
Finding secondary services using dongle, linux library 0

Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0. I can see/connect to the device I am trying...
- nrf51dongle service discovery
523 views

0 replies

Started over 7 years ago
by timrcooper
Not Answered
what facter will influence the speed of sending data 0

when use sd_ble_gatts_hvx() send data must need 300ms what facter will influence the speed of sending data ,please help me ,thank you very much
- 10040 nrf52832 s132
555 views

0 replies

Started over 7 years ago
by happykelvin
Not Answered
nRF52: OneWire HDMI CEC 0

Hey, I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832. I would be very grateful if anybody could share the library or give...
- nrf52
- one-wire
1579 views

0 replies

Started over 7 years ago
by Sorrow91

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022