Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Unable to see NRF_LOG BLE SDK 12.3 0

I am using SEGGER Studio on MacOSx. When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio. However...
- nrf51822 nrf_log segger
945 views

0 replies

Started over 7 years ago
by zed
Not Answered
nRF Cloud Gateway Error connecting gateway 0

Hello, I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
- nrf52 pca10040 nrfconnect
- nrfCloud
1417 views

0 replies

Started over 7 years ago
by carlos carrizosa
Not Answered
Finding secondary services using dongle, linux library 0

Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0. I can see/connect to the device I am trying...
- nrf51dongle service discovery
537 views

0 replies

Started over 7 years ago
by timrcooper
Not Answered
what facter will influence the speed of sending data 0

when use sd_ble_gatts_hvx() send data must need 300ms what facter will influence the speed of sending data ,please help me ,thank you very much
- 10040 nrf52832 s132
573 views

0 replies

Started over 7 years ago
by happykelvin
Not Answered
nRF52: OneWire HDMI CEC 0

Hey, I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832. I would be very grateful if anybody could share the library or give...
- nrf52
- one-wire
1600 views

0 replies

Started over 7 years ago
by Sorrow91

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020