Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Wouldn't update connection params 0

Hi, I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init: static void conn_params_init(void){ uint32_t err_code; ble_conn_params_init_t...

715 views

0 replies

Started over 7 years ago
by Alice
Not Answered
how to use whitelist in ble_app_hrs_c 0

S130, SDK 12.3, ble_app_hrs_c example. I want to use whitelist function in this example but I can't finish it. When I run peer_list_get(), it gets all 0xFF, means that...
- s130
- whitelist
- ble_app_hrs_c
- nrf51822
873 views

0 replies

Started over 7 years ago
by kamisen
Not Answered

services size is zero 0

sometime,i use android app to scan ble device,it will display "the device dose not has required services",the gatt.getServices.size is zero.why?

533 views

0 replies

Started over 7 years ago
by nowen
Not Answered
one wire library for nrf51822 keil 0

one wire library for nrf51822 keil for connected ds18b20 .
- nrf51822 keil one wire
745 views

0 replies

Started over 7 years ago
by morteza1994
Not Answered
Nordic NFR52832 Two Masters with FTDI SPI-USB Bridge 0

Hi all, I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
- c232hm
- adc
- qt
- nfr52832
- ftdi bridge
- spi
- keil
- spi-usb
972 views

0 replies

Started over 7 years ago
by bryanhsieh

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020