Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to further improve the transmission rate in ESB 2.4G proprietary protocols? 0

I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
24 views

0 replies

Started 1 day ago
by Cytheria
Not Answered
some reasons cause "No connection for handle 0" 0

Hi, nordic team There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0. peripheral side is programmed base on peripheral_hid_keyboard and...
36 views

0 replies

Started 1 day ago
by Martin Evans
Not Answered
warning: Experimental symbol MODEM_MODULES is enabled. 0

Hi all, We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1 When compiling the Serial...
30 views

0 replies

Started 1 day ago
by jamawa
Not Answered
Application Crashes When Enabling Both 1M and Coded PHY in BLE Scan Init 0

Hi, I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
48 views

0 replies

Started 1 day ago
by Nikunj089
Not Answered
Optimizing 10 kHz Data Stream Merging & De-duplication 0

Hi all, I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
- development
- code
- software
- nRF52833
- 2.4 ghz
- proprietary
- C
37 views

0 replies

Started 1 day ago
by Floppey

Recent in Nordic blog

Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018
Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018